-- **********************************************************************
-- EOSN-PARTITIONING-MIB: McDATA EOSN Partitioning Enterprise MIB (SMIv2).
--
-- The nSCALE Dynamic Partition (nDP) group
-- Only users of the admin partition can access this group.
--
-- REVISION HISTORY
-- Date PRG Description
-- ======================================================================
-- Release 1.0
--
-- 06/18/04 xli Renamed "sanera" to "eosn"
-- 02/20/04 xli changed 0-based index to 1-based
-- 02/12/03 dhl Updated assignment and config tables
-- 02/25/02 sto Initial version
--
-- Copyright (c) 2003 McDATA Corp. All rights reserved.
-- Copyright (c) 2002-2003 Sanera Systems, Inc. All rights reserved.
-- **********************************************************************
--EOSN-PARTITIONING-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,OBJECT-IDENTITY,NOTIFICATION-TYPE,TimeTicks,IpAddress,Counter32,Counter64,Integer32,Unsigned32,Gauge32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,TruthValue,RowStatus,DisplayString,TimeStampFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
BbSlotNumber, BbPartitionNumber FROM EOSN-TC
eosnModules, eosnMIB FROM EOSN-REG
bbPartitioning FROM EOSN-MIB;eosnPartitioningModule MODULE-IDENTITYLAST-UPDATED"0406181759Z"ORGANIZATION"McDATA Corporation"CONTACT-INFO" McDATA Corporation
Postal: 370 San Aleso Ave
Sunnyvale, CA 94086
USA
Tel: +1-408-734-6000
E-mail: support@mcdata.com
Web: www.mcdata.com
"DESCRIPTION"This MIB module describes dynamic partitioning objects for
the Big Bang system."REVISION"0302120000Z"DESCRIPTION"Initial version."
::={ eosnModules 5}bbPartitioningMaxSupported OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum number of dynamic partitions supported by the system.
This object is accessible only on the admin partition."::={ bbPartitioning 1}bbPartitionConfigTable OBJECT-TYPESYNTAXSEQUENCEOF BbPartitionConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table for configuration of the partitions.
This table is accessible only on admin partition."::={ bbPartitioning 2}bbPartitionConfigEntry OBJECT-TYPESYNTAX BbPartitionConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry of the partition table."INDEX{ bbPartitionConfigIndex }::={ bbPartitionConfigTable 1}
BbPartitionConfigEntry ::=SEQUENCE{
bbPartitionConfigIndex BbPartitionNumber,
bbPartitionConfigName DisplayString,
bbPartitionConfigIpAddress IpAddress,
bbPartitionConfigState INTEGER,
bbPartitionConfigPeerSyncStatus INTEGER,
bbPartitionConfigCommand INTEGER}bbPartitionConfigIndex OBJECT-TYPESYNTAX BbPartitionNumber
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A unique index to identify this partition."::={ bbPartitionConfigEntry 1}bbPartitionConfigName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The name of this partition."::={ bbPartitionConfigEntry 2}bbPartitionConfigIpAddress OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"The IP address of this partition."::={ bbPartitionConfigEntry 3}bbPartitionConfigState OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The state of this partition."::={ bbPartitionConfigEntry 4}bbPartitionConfigPeerSyncStatus OBJECT-TYPESYNTAXINTEGER{unknown(1),standAlone(2),active(3),standbySyncing(4),standbyReady(5),outOfService(6)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The peer (remote CTP) sync status of this partition."::={ bbPartitionConfigEntry 5}bbPartitionConfigCommand OBJECT-TYPESYNTAXINTEGER{none(1),enable(2),enableClean(3),disable(4),restart(5)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is used to issue a command to this partition.
SET operation Description
-------------- ------------------------------------------------
enable(2) To enable a partition retaining previous configuration.
enableClean(3) To enable a partition with a clean (default) configuration.
For enable and enableClean, the following objects must have
valid values so they can be used as defaults:
bbPartitionConfigName
bbPartitionConfigIpAddress
disable(4) To disable a partition. A partition can be disabled only
if it has no slots assigned to it.
restart(5) To restart a partition. A partition can be restarted even
if it owns slots.
On a GET, none(1) is return."::={ bbPartitionConfigEntry 6}bbPartitionSlotAssignmentTable OBJECT-TYPESYNTAXSEQUENCEOF BbPartitionSlotAssignmentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table for assigning slots to partitions. This table is
accessible only on the admin partition."::={ bbPartitioning 3}bbPartitionSlotAssignmentEntry OBJECT-TYPESYNTAX BbPartitionSlotAssignmentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry of the slot assignment table."INDEX{ bbPartitionSlotAssignmentIndex }::={ bbPartitionSlotAssignmentTable 1}
BbPartitionSlotAssignmentEntry ::=SEQUENCE{
bbPartitionSlotAssignmentIndex BbSlotNumber,
bbPartitionSlotAssignmentOwner Integer32}bbPartitionSlotAssignmentIndex OBJECT-TYPE
SYNTAX BbSlotNumber
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A unique index to identify the slot to assign. The number equals the slot number + 1."::={ bbPartitionSlotAssignmentEntry 1}bbPartitionSlotAssignmentOwner OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The new partition owner to assign this slot to. When a
new partition owner is assigned, this slot leaves the current
partition and joins the new partition. On a GET, this value
indicates the owner of the specified slot."::={ bbPartitionSlotAssignmentEntry 2}END